On this page in the next paragraph you will find more incredibly good news all about How to Install a Bathtub Yourself.
Installing a bath tub isn't precisely rocket science, yet it does need solid plumbing, carpentry, as well as often, tiling skills. Replacing an old bath tub with a brand-new one is likewise a moderately challenging job. If the old tub is readily available, the task can relocate quickly; if you have to open up a wall surface to get rid of the old tub and place the new bathtub, the job is much harder. In either instance, the task is within a house handyman's skills, although you will certainly require a helper to move out the old bathtub and also set in the brand-new one. Make sure you have actually qualified on your own for the work as well as are comfortable attempting it. As opposed to employing a professional to take over a halfway-completed job, it is better to think about utilizing one before you begin. Opportunities are you may require an expert plumber to make tube links.
This article will certainly help you set up a new bath tub in your restroom if you have actually currently bought a brand-new tub and don't need to transform the plan of your previous water supply pipelines.
Your tools as well as product checklist need to comprise the following:
Preparing for the Setup
First of all, the sustaining framework provided with the bathroom needs to be fitted (if required) according to the maker's instructions. Next off, fit the taps or mixer to the bathtub. When suitable the tap block, it is essential to ensure that if the faucet includes a plastic washer, it is fitted between the bath and the faucets. On a plastic bath, it is likewise sensible to fit a supporting plate under the taps unit to prevent strain on the tub.
Fit the adaptable faucet ports to the bottom of the two faucets using 2 nuts and olives (sometimes provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet with the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Make certain you make use of every one of the provided washers.
Attach the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a comparable manner.The bathroom should currently be ready to be suited its final position.
Removing Old Touches
If you require to change old taps with brand-new ones as a part of your installment, then the first thing you need to do is disconnect the water system. After doing so, activate the taps to drain pipes any type of water staying in the system. The process of getting rid of the existing taps can be rather troublesome because of the restricted gain access to that is often the situation.
Make use of a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipes to the faucets. Have a cloth all set for the remaining water that will come from the pipes. Once the supply pipelines have been eliminated, use the very same device to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the solitary faucets from transforming during this process. As soon as the taps have been eliminated, the holes in the bath/basin will have to be cleaned of any old sealing compound.
Before carrying on to fit the brand-new taps, compare the pipe links on the old taps to the brand-new faucets. If the old taps are longer than the new taps, then a shank adapter is needed for the brand-new faucets to fit.
Installing the Tub
Using the two wooden boards under its feet, place the bath tub in the called for position. The wooden boards are useful in uniformly spreading out the weight of the bathtub over the location of the boards rather than focusing all the weight onto four small factors.
The next objective is to make sure that the bath tub is leveled all round. This can be attained by examining the level and changing the feet on the tub up until the spirit level checks out level.
To mount taps, fit all-time low of the outermost adaptable tap port to the ideal supply pipeline by making a compression sign up with; after that do the exact same for the various other tap.
Switch on the supply of water and also examine all joints and also new pipework for leaks and tighten them if required. Fill up the tub as well as also examine the overflow electrical outlet and the typical outlet for leakages.
Finally, repair the bath paneling as explained in the supplier's instruction manual. Tiling as well as sealing around the tub should wait up until the tub has been used a minimum of when as this will resolve it into its final setting.
Fitting New Touches
If the tails of the brand-new taps are plastic, then you will certainly require a plastic connector to avoid damages to the string. One end of the adapter fits on the plastic tail of the tap and also the various other end provides a connection to the existing supply pipes.
If you need to fit a monobloc, after that you will certainly call for minimizing couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next, place the faucet in the installing hole in the bath/basin ensuring that the washers are in location in between the tap and the sink. Protect the faucet in place with the producer given backnut. As soon as the tap is firmly in position, the supply pipes can be connected to the tails of the taps. The taps can either be attached by using corrugated copper piping or with regular tap ports. The previous type ought to be linked to the faucet finishes first, tightening just by hand. The supply pipes can later be attached to the various other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the location where the bath meets the tile, it is essential to seal the accompanies a silicone rubber caulking. This is essential as the installation can move enough to split an inflexible seal, triggering the water to pass through the wall in between the bathroom as well as the tiling, causing difficulties with moisture and also possible leaks to the ceiling listed below.
You can choose from a selection of coloured sealants to blend in your fixtures and also installations. They are sold in tubes and also cartridges, as well as can securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger void to fill up, you can load it with twists of soaked newspaper or soft rope. Keep in mind to constantly fill the bathtub with water before sealing, to permit the movement experienced when the bathtub is in use. The sealer can fracture rather early if you do not think about this motion before securing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also quickly readily available on the marketplace. It is a good idea to fit the tiles utilizing water-resistant or waterproof adhesive and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you like reading about A Step-by-Step Guide to Installing a Bathtub? Create a short review directly below. We would be pleased to listen to your views about this write-up. Hoping that you come back again in the future. Are you aware of another individual who is occupied with How to Install a Bathtub Yourself? Feel free to share it. Thanks a lot for your time invested reading it.
Toilet overflow? Call us!